Replacing one end of an old hdmi cable - AVS Forum
Dec 29, 2019 · Show Me cables has a similar unit. The HDMI male end is around $15 but you also need the crimper to complete the repair which is around $125-$150. There is a solderless, screw down breakout terminal block HDMI connector sold under the brand names of Oiyagai, SinLoon and some other brand names.
Can an HDMI cable end be repaired? - AVS Forum
Apr 27, 2009 · Quote: Originally Posted by kciaccio /forum/post/16363960. Tie string (nylon used by pros) to your old cable, pull your old cable out. Pull new cable in with nylon string. I wish I had that option. The wholes on the studs are just big enough for the connector, now that other cable is ran, its to tight to pull cable.
Cutting the end of a fiberoptic hdmi cable? - AVS Forum
Jun 18, 2018 · I agree with the suggestions above. Either just cut a hole small enough to fit the cable intact thru and then patch the hole around the cable or, preferably, use a pass thru wall plate. The pass thru wall plate gives the flexibility of replacing the cable if …
How to fix an HDMI Cable. For real. - AVS Forum
Oct 20, 2010 · 1) Use the cable shield as a return wire for the meter. 2) Drag a long piece of doorbell wire to the other cable end and use it as a meter probe extension. However the impedance matching issues of an HDMI cable splice are major. It's not just a matter getting the right pins tied together, that's the easiest part.
HDMI Cable Only Works in One Direction? - AVS Forum
Apr 30, 2013 · Originally Posted by Colm /t/1470683/hdmi-cable-only-works-in-one-direction#post_23269553. Yes, the Redmere technology is contained in a small chip in the sink end connector. It isn't an amplifier in the simple sense. It …
how to pull (HDMI) cable through existing conduit? | AVS Forum
Mar 14, 2013 · Protect the HDMI connector by wrapping it in paper and taping around it, secure the pull string to the cable behind the connector. Attach a new pull string to be pulled along (so you have something to pull the next cable that needs to go in). Have someone feed the HDMI cable into the conduit at one end while another person slowly pulls the ...
HDMI - Ground noise in amp "Solved" via ground... - AVS Forum
Oct 12, 2012 · Basically I could stop the hum by unplugging the HDMI cable from my HTPC then just brushing the edge of the HDMI cable end against the HDMI port of the AVR it would come back. The fiber HDMI cable did reduce the hum to about 15-20% of what it was, but it was still audible. I then went the route of a ground loop isolator for RCA cables.
Any tips for pulling HDMI cable through conduit? - AVS Forum
Mar 30, 2015 · 6160 posts · Joined 2007. #9 · Mar 31, 2015. Make sure you don't put stress on the HDMI connector end - extend the wrapped tape back to the HDMI and category cable jackets. Make sure the Redmere cable is pulled correctly, as it's directional; won't work backwards.
What is best way to run HDMI cable through conduit?
Mar 14, 2010 · Go slow and try and do 6"-12" at a time. Never pull the cable by the connector. If you need to pull a little more in at one end or the other grab the cable about 6 inches back from the connector. Once the cable is thru remove the electrical tape and wipe off any hand soap and then unwrap the HDMI connector.
Short List of Certified HDMI Cables for HDMI 2.1 - AVS Forum
Dec 10, 2021 · There is no performance difference in cables rated for CL and those that are not. The cables mfrs listed below offer CL-rated HDMI cables: Hybrid Fiber. Ruipro 8k, CL2, not certified, 1m - 100m. Cable Matters 8k, CL2, not certified, 8m - 15m. Wireworld Starlight 48, CL2, ATC Certified, 5m,10m,15m, 20m, 30m.